Extraflame Pellet Stoves Manuál s instrukcemi

Stufe a PelletCarefully read the instructions before installing, using and maintaining.The instructions book is an integral part of the product.Lucrez

SAFETY DEVICES10Chapter 3 INSTALLATION AND SAFETY DEVICESThe installation, relative plant connections, commissioning and inspection of correct functio

SAFETY DEVICES11Chapter 3 SAFETY DEVICES FOR CLOSED VESSEL PLANTAccording to the UNI 10412-2 (2006) Standard in force in Italy, the closed plants mus

12ASSEMBLY AND INSTALLATION INSTRUCTIONSChapter 4ASSEMBLY AND INSTALLATION INSTRUCTIONSThe installation must comply with:UNI 10683 (2005) heat generat

13ASSEMBLY AND INSTALLATION INSTRUCTIONSChapter 4EXHAUST VENTING SYSTEMA system for fume exhaust venting that is independent from the appliance, compo

45°<45°<14Chapter 4ASSEMBLY AND INSTALLATION INSTRUCTIONSCONNECTION TO THE EXHAUST VENTING SYSTEMEXHAUST CHANNEL OR PIPEFor the assembly of the

BC20 cmA15ASSEMBLY AND INSTALLATION INSTRUCTIONSChapter 4the  ue connection.It is forbidden to run other air feed channels or piping for utilities in

< 3 m3 - 5 %< 3 m45°45°16Chapter 4ASSEMBLY AND INSTALLATION INSTRUCTIONSInspectionWindproof chimney capFlueInspectionExternal insulated ductInsp

50 cm< 5 m> 5 m< 5 m50H minβ17ASSEMBLY AND INSTALLATION INSTRUCTIONSChapter 4CONNECTION TO THE FLUE AND COMBUSTION PRODUCT EXHAUST VENTINGThe

18Chapter 4ASSEMBLY AND INSTALLATION INSTRUCTIONSCHIMNEYS, DISTANCES AND POSITIONINGRoof pitchDistance between the crown and the chimneyMinimum height

PRODUCT FUNCTIONALITY19Chapter 5 Chapter 5 PRODUCT FUNCTIONALITYCONTROL BOARDREMOTE CONTROL SENSORD1 D21 D ON/OFF BUTTONBy pressing button 1 it is pos

2

PRODUCT FUNCTIONALITY20Chapter 5 Commands procedureRemove and restore the stove power supply using the master switch or using the power supply 1. cabl

PRODUCT FUNCTIONALITY21Chapter 5 ING1 D connection input between clamps ING1 and COM of the terminal boardING2 D connection input between clamps ING2

PRODUCT FUNCTIONALITY22Chapter 5 Commands procedureRemove and restore the stove power supply using the master switch or using the power supply 1. cabl

PRODUCT FUNCTIONALITY23Chapter 5 The stove works controlling the state of the priority input (ING1): when the thermostat results satis ed, the stove

PRODUCT FUNCTIONALITY24Chapter 5 State of clamps State of outputs State of stoveING1 external contact connectedING2 external contact connectedING1 clo

PRODUCT FUNCTIONALITY25Chapter 5 The stove you have purchased uses pellet fuel. This type of material is obtained from natural waste from the machinin

PRODUCT FUNCTIONALITY26Chapter 5 NORMAL FUNCTIONINGWhen ignition has taken place, the user can adjust the heating power using buttons 4 and 5. By pres

27REMOTE CONTROLChapter 6Chapter 6REMOTE CONTROLThe heat setting, the temperature, and automatic start/stop of the stove can be remote controlled.To l

WATER TEMPERATURE ADJUSTMENT28Chapter 7 Chapter 7 WATER TEMPERATURE ADJUSTMENTThe appliance can control the water temperature through a digital proble

USER PARAMETERS29Chapter 8 Chapter 8 USER PARAMETERSUSER PARAMETERSWEEKLY PROGRAMMERDisplay D1 Display D2 FunctionOFF UT 0 Act./Deact. Weekly programm

3 Congratulations! You are now the owner of an Extra ame stove!The Extra ame pellet stove is an ideal heating solution. It utilises the most advance

30Chapter 8 ParameterFunctionAdjustment KeysValueCon rmation KeyDisplay D2 Display D1 UT 0 Act. /deact. weekly programmer 2 or 3 ON/OFF 5UT 1 Time 1

USER PARAMETERS31Chapter 8 To con rm and continue programming, press button 5.Press button 4 to go back to the previous parameter.Parameter 4 (D2=4(

32Chapter 8 Parameter A (D2=A( ashing); D1=Ex. “OFF 1”)At this point the values introduced in this parameter have no value as the ignition and switc

USER PARAMETERS33Chapter 8 Adjustment tableLACK OFFUELIncrease the percentage value by 5 points and try the stove with the new calibration for at leas

CLEANING34Chapter 9 Chapter 9 CLEANINGMaintenance operations guarantee correct functioning of the product through time.Failure to comply with these op

CLEANING35Chapter 9 DOOR AND ASH DRAWERS GASKETSThe gaskets guarantee the tightness of the stove and its consequent good functioning.These must be che

COMMISSIONING OPERATIONS36Chapter 10 Chapter 10 COMMISSIONING OPERATIONSMOUNTING THE TILES ONLY LUCREZIA IDROThe tiles mounting operations must be c

COMMISSIONING OPERATIONS37Chapter 10 Position the side tiles in the appropriate 5. iron hooks, starting from the bottom upwards, in the two sides of t

COMMISSIONING OPERATIONS38Chapter 10 BRAZIER BRACKETBefore igniting the stove, make sure to have removed the bracket indicated in the  gure. Remove t

PRODUCT DISPLAY TABLES39Chapter 11 PRODUCT DISPLAY TABLESSIGNALSSIGNALSREASON SOLUTIONDISPLAYWAIT FOR COOL.A new ignition is attempted when the stove

4

PRODUCT DISPLAY TABLES40Chapter 11 ALARMSSIGNALSREASON SOLUTIONDISPLAY D1Indicates the presence of an alarm.It is on in the presence of one of the ala

PRODUCT DISPLAY TABLES41Chapter 11 WAIT FOR COOL.+ ALARMAttempt to release the alarm with stove still in cooling mode.Every time the stove displays on

PRODUCT DISPLAY TABLES42Chapter 11 LUMINOUS INDICATORSSIGNALSREASON SOLUTIONINDICATOR LIGHTIt indicates weekly programmer functioning.It is on/o whe

WARRANTY CONDITIONS43EXTRAFLAME S.p.A., with o ces in via dell’Artigiananto 10 Montecchio Precalcino (VI), warrants this product for 2 (two) YEARS

etichetta codice a barreQUALITY CONTROL44QUALITY CONTROL

45Notes

46Notes

47Notes

Manuale utente Lucrezia Idro - Lucrezia SteelREV 018 25.11.09Stufe a PelletEXTRAFLAME S.p.A.Via Dell’Artigianato, 1036030 MONTECCHIO PRECALCINOVicenza

5IndexChapter 1 WARNINGS AND SAFETY DEVICES...

6EXTERNAL THERMOSTAT FUNCTIONING IN STBY/TOFF MODE TO ALSO BE USED FOR TELEPHONIC ACTUATOR ...

WARNINGS AND SAFETY DEVICES7Chapter 1 The stoves produced by our establishment are built with attention to the individual components in a way to prote

Chapter 2 WHAT IS THE PELLET?Pellets are realised by subjecting wood shavings i.e. the rejects of pure wood (without paint) sawmill, carpenter product

SAFETY DEVICES9Chapter 3 Chapter 3 SAFETY DEVICESFLUE EXHAUST BREAKAGEIf the suction device stops, the electronic board immediately blocks the pellet